I'll create the content for design/campaigns/standees/installation.md:

Standee Installation Guide¶

Installation Essentials

Successful standee installation requires:
- Proper preparation
- Correct assembly
- Secure placement
- Safety verification
- Regular checks

Pre-Installation Planning¶

Setup Requirements¶

graph TD
    A[Planning] --> B[Site Check]
    A --> C[Tools Ready]
    A --> D[Parts Check]
    B --> B1[Location]
    C --> C1[Equipment]
    D --> D1[Inventory]

Installation Checklist¶

Phase	Requirements	Verification	Tools
Site Prep	Clear space	Measurement	Tape measure
Tools	Required equipment	Inventory	Tool kit
Parts	All components	Count	Checklist
Area	Adequate space	Measurement	Space marker

Assembly Process¶

Component Assembly¶

Step	Action	Tools	Time
Base setup	Position base	Level	5 mins
Pole assembly	Connect poles	None	5 mins
Panel mount	Attach panel	Brackets	10 mins
Stabilization	Secure structure	Level	5 mins

Assembly Flow¶

flowchart LR
    A[Unpack] --> B[Base]
    B --> C[Structure]
    C --> D[Panel]
    D --> E[Secure]

Installation Steps¶

Step-by-Step Guide¶

Stage	Procedure	Check Points	Notes
1. Location	Mark position	Floor marks	Use template
2. Base	Place & level	Stability	Check surface
3. Structure	Assemble poles	Alignment	Verify fit
4. Panel	Mount display	Security	Check tension

Quality Checks¶

pie title "Installation Verification"
    "Stability" : 30
    "Alignment" : 25
    "Security" : 25
    "Appearance" : 20

Safety Measures¶

Safety Requirements¶

Aspect	Standard	Verification	Action
Stability	No wobble	Physical test	Adjust base
Clearance	3ft minimum	Measurement	Reposition
Access	Clear path	Visual check	Clear area
Security	All locks engaged	Test locks	Tighten

Safety Protocol¶

graph TD
    A[Safety] --> B[Check]
    B --> C[Test]
    C --> D[Verify]
    D --> E[Document]

Tool Requirements¶

Essential Tools¶

Tool	Purpose	Specification	Notes
Level	Alignment	Standard	Digital preferred
Tape measure	Spacing	5m minimum	Metric/Imperial
Markers	Position	Non-permanent	Floor safe
Tool kit	Assembly	Basic set	Phillips/Flat

Optional Equipment¶

Item	Use Case	When Needed	Alternative
Drill	Anchoring	Permanent install	Manual tools
Light	Visibility	Dark areas	Work lights
Gloves	Protection	Heavy parts	Hand protection
Cart	Transport	Multiple units	Hand carry

Location Verification¶

Position Checks¶

flowchart LR
    A[Position] --> B[Level]
    B --> C[Secure]
    C --> D[Clear]
    D --> E[Final]

Verification Points¶

Check	Method	Standard	Action
Position	Measure	Per plan	Adjust
Level	Spirit level	True level	Balance
Stability	Physical test	No movement	Secure
Clearance	Measure	3ft minimum	Reposition

Maintenance Procedures¶

Regular Checks¶

Item	Frequency	Check Points	Action
Stability	Daily	Base secure	Adjust
Structure	Weekly	Connections	Tighten
Panel	Monthly	Tension	Adjust
Hardware	Monthly	All parts	Replace

Maintenance Schedule¶

gantt
    title Maintenance Timeline
    dateFormat YYYY-MM-DD
    section Checks
    Daily Review     :a1, 2024-01-01, 1d
    Weekly Check    :a2, 2024-01-01, 7d
    Monthly Service :a3, 2024-01-01, 30d

Troubleshooting Guide¶

Common Issues¶

Problem	Cause	Solution	Prevention
Wobble	Uneven surface	Adjust base	Check floor
Lean	Poor assembly	Reassemble	Follow guide
Loose panel	Wear	Tighten	Regular checks
Damage	Impact	Repair/Replace	Clear area

Resolution Process¶

graph TD
    A[Issue] --> B[Diagnose]
    B --> C[Fix]
    C --> D[Test]
    D --> E[Document]

Installation Success Tips

Follow sequence
Check stability
Verify position
Document setup
Regular maintenance

Resources¶

Installation Tools¶

Setup guide
Tool checklist
Safety guidelines
Maintenance log
Troubleshooting guide

View Materials → Check Specs →